1.1 This practice describes the proper procedures for preserving zooplankton samples with either formaldehyde, ethanol, glutaraldehyde, Lugol's iodine solution, or vinegar (
2004-04-01
1.1 This terminology is used or is likely to be used in test methods, specifications, guides, and practices related to agricultural tank mix adjuvants. 1.2 These definitions are written to ensure ...
2011-05-20
1.1 This practice describes procedures for fabricating both green and sintered test bars of silicon carbide and silicon nitride containing both internal and surface voids at prescribed locations. 1...
2004-05-01
1.1 This test method covers the determination of elastic properties of “as produced” elastomeric yarns made from rubber, spandex or other elastomers. Elastic propertie
2007-01-01
1.1 This test method covers a method of measuring the water resistance of footwear. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is th
1.1 This guide provides recommendations for the selection of appropriate test methods for prefabricated vertical geocomposite drains (sometimes referred to as Wick Drains) used in geotechnical engi...
2007-09-05
1.1 This test method covers an instrumental method for the CIE (Commission International de l'Eclairage) tristimulus measurement of the color of near-clear liquid samples. The measurement is co...
2010-01-01
1.1 This test method covers the determination of hydrogen in petroleum fractions that can be burned completely without smoking in a wick lamp. 1.2 The values stated in SI units are to be regarded a...
2011-09-16
1.1 This test method covers obtaining, preparing, and testing cores drilled from shotcrete for length, compressive strength, or splitting tensile strength determinations.</div
2005-01-01
1.1 This specification covers perforated concrete pipe intended to be used for underdrainage. 1.2 This specification is the inch-pound companion to Specification C 444M; therefore, no SI equivale...
2003-01-10
1.1 These test methods cover the testing of fibrous-insulated electrical conductors, commonly referred to as magnet wire, which are used in electrical apparatus. The test methods are intended prima...
1.1 This test method covers the procedure for the quantitative separation of the vehicle from the pigment in solvent-reducible coatings. 1.2 This test method has been proven to be applicable to t...
2010-12-01
1.1 This guide covers the dispersion in liquids of metal powders and related compounds for subsequent use in particle size analysis instruments. This guide describes a general procedure for achievi...
2010-10-15
1.1 This test method determines total lead in gasolines containing lead alkyls at concentrations between 0.026 and 1.3 g Pb/L, and 0.12 and 6.0 g Pb/UK gal, 0.1 and 5.0 g Pb/US gal. 1.2 The values ...
2005-05-01
1.1 This guide provides procedures and criteria for the development and use of sediment/water microcosms for laboratory evaluations of the fate of chemical substances in the environment. It does no...
2008-02-01
2013-03-15
1.1 This specification establishes the requirements for copper-nickel alloy castings with nominal compositions shown in Table 1. These are as follows: <td a
2009-04-01
1.1 This specification covers the material requirements for high-purity, dense aluminum oxide for surgical implant applications. 1.2 The values stated in SI units are to be regarded as the standa...
2000-04-01
2009-03-05
1.1 This guide covers the techniques for obtaining approval for release of materials encountered in decontamination and decommissioning (D&D) from restricted use. This would be addressed...
2009-06-01
1.1 This test method is a performance test for acceptance of sieves. 1.2 This test method compares the performance of a sieve against an inspection or calibration sieve using a known quantity of re...
2011-12-16
1.1 This practice describes the procedures and equipment used to collect surface and subsurface soil and contaminated media samples for chemical analysis using a hand-operated bucket auger (hereaft...
2005-02-01
1.1 This practice covers a procedure for the division of shipments of manufactured staple fiber, sliver (or top) or tow into lots and the sampling of such lots for testing. Note 1&
1.1 This guide covers the development or assessment of environmental monitoring plans for decommissioning nuclear facilities. This guide addresses: (1) development of an environmental baseline prio...
2011-03-18
1.1 This practice covers the assignment of a value to property that provides an economic and logical basis for efficient and cost-effective property management. This value should be the basis for a...
2002-07-10
1.1 This specification covers the composition and physical properties of polyimide foam insulation with nominal densities from 1.0 lb/ft3 to 8.0 lb/ft3 (16 kg/m3 to 128 kg/m3) and intended for use ...
2012-02-24
1.1 These test methods cover photometric procedures for the chemical analysis of copper and copper alloys having chemical compositions within the following limits:1.2 The analytical procedures appe...
2004-06-01
2010-03-01
1.1 The table provides a standard ultraviolet spectral irradiance distribution that maybe employed as a guide against which manufactured ultraviolet light sources may be judged whe
2008-06-01
1.1 This practice covers guidelines for utilizing EMAT techniques for detecting material discontinuities that are primarily open to the surface (for example, cracks, seams, laps, cold shuts, lamina...
1.1 This test method is designed to evaluate paintball barrier netting that may be used to delineate playing fields, chronograph areas, target ranges, and other “goggle-on”</s
2010-07-01
1.1 This test method covers the total solids and ash content of finishing materials. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in ...
2006-10-01
1.1 This specification covers sheet steel in coils and cut lengths for porcelain enameling. The compositions and processing of these steels are such that articles for porcelain enameling may be fa...
2009-11-01