1.1 This test method covers measurements of lamination factor (Note 1) of a specimen composed of strips cut from amorphous magnetic materia
2006-05-01
1.1 This specification pertains to quicklime and hydrated lime, either high calcium, dolomitic, or magnesian lime, for use in stabilization of soils (See Note 2). Note 1— This specifica...
2011-03-18
1.1 This test method covers the determination of the nonvolatile matter remaining after a specimen of fatty quaternary ammonium chloride is completely burned and ignited. 1.2 This standard does ...
1992-01-01
2007-03-20
1.1 This test method establishes a procedure for testing components used in ultra-high-purity gas distribution systems for ionic and organic surface residues. <div class=
1999-06-10
1.1 This specification establishes the requirements for copper-nickel-zinc and copper-nickel rod and bar for general application produced from Copper Alloy UNS Nos. C70600, C70620, C71500, C71520, ...
2005-10-01
1.1 This test method covers the determination of the hydroxyl content of castor oil, dehydrated castor oil, and their derivatives. This test method may also be used for other fatty products such as...
1986-03-27
2007-03-02
1.1 These test methods cover the determination of the amount of constituents in petroleum products such as lubricants, additives, and transmission fluids that will saponify under t
2007-09-05
1.1 This practice covers the use of the reflectance-type optical character testers with a 0.008-in. (0.203-mm) aperture as test instruments for measuring image quality. 1.2 Although other systems m...
2009-10-01
1.1 This practice provides guidance for the functional, kinematic and wear testing of motion-preserving total facet prostheses for the lumbar spine. These implants are intended to
2008-02-06
1.1 This specification covers straight seam or spiral seam electric-fusion-welded, light-wall, austenitic chromium-nickel alloy steel pipe for corrosive or high-temperature service. The sizes cove...
1.1 This guide is intended to assist in the selection of walkway surfaces where the presence of foreign materials may produce the danger of a slip or a fall.1.2 This standard does not purport to ad...
2003-01-10
2012-07-10
1.1 This terminology contains related definitions and descriptions of terms used or likely to be used in medical packaging standards that involve barrier materials. The purpose of terminology is to...
2005-04-01
2007-04-01
1.1 This test method is used to evaluate the virucidal efficacy of liquid, aerosol, or trigger-spray microbicides intended for use on inanimate, nonporous environmental surfaces. This test method m...
2011-05-20
1.1 This practice covers an indication of the quality of recycled transparent poly(ethylene terephthalate) by examination of a wafer or plaque formed by melting a representative sample and quenchin...
2011-04-15
1.1 This specification establishes the requirements for phosphorized copper wire bars, billets, and cakes. Note 1—Wire bars furnished under this specification do not conf This specifica...
2011-06-17
1.1 Purpose: 1.1.1 The primary purpose of this practice is to provide guidance for making adequate thermal balance tests of spacecraft and components where solar simula This practice provides guid...
2010-04-01
1.1 This test method covers the determination, without reference to a material paint standard, of the hiding power of air dry coatings with Y tristimulus values greater than 15 %. With appropriat...
2011-09-16
1.1 This method covers the specific determination of the effect of short-radius bends on coatings applied to 33.4-mm (1-in. nominal) diameter pipe. 1.2 The values stated in SI units to three signi...
1.1 This specification provides the requirements for mattresses and box springs that are for use in berths for officers, crew, and passengers in marine vessels. This shall be considered a minimum s...
1.1 This test method describes a procedure to measure open assembly time for a troweled carpet adhesive. 1.2 This test method provides an evaluation of the ability of an adhesive to effectively wet...
2004-04-01
1.1 This specification covers silver-coated, round, copper-clad steel wire for electronic application. 1.2 Silver coatings in mass percentages of the total mass of the coated wire are as follows: 1...
2010-05-17
1.1 These test methods cover the procedures for determining the asphalt content of samples of uncompacted bituminous mixtures (Test Method A), and of laboratory compacted specimens of bituminous m...
1.1 This specification covers commercial multiple-tank dishwashing machines of the continuous type, oval shaped, with horizontal table conveyor systems. 1.2 The values stated in inch-pound units a...
1.1 This test method describes procedures for determining the washability characteristics of coarse-coal fractions and fine-coal fractions. Each sample being tested can have more t
2006-09-01
1.1 This standard covers solvents based on stabilized normal-propyl bromide (nPB) for use in vapor degreasing. The standard also includes a separate specification for technical-grade This specifica...
2006-06-01
1.1 This test method covers the determination of the permeability of leather to water vapor by measuring the rate at which water vapor passes through a test specimen. This test method does not app...
1.1 This practice covers compression test in which the specimen is heated to a constant and uniform temperature and held at temperature while an axial force is applied at a controlled rate of strai...
2005-12-01
1.1 This guide covers the identification of metals and alloys in computerized material property databases. It establishes essential and desirable data elements that serve to uniquely identify and d...
2009-09-01
1.1 This practice outlines a procedure to obtain a record of normalized resistance of sands to the penetration of a standard sampler driven by a standard energy for estimating soil liquefaction pot...
2012-02-24
1.1 This test method covers the determination of lead and cadmium extracted by acetic acid from the lip and rim area of glassware used for drinking and which is exteriorly decorated with ceramic gl...
2004-10-01