21293 träffar på

Standard · ASTM ASTM F565 Standard Practice for Care and Handling of Orthopedic Implants and Instruments 1.1 This practice covers recommended procedures for the handling of orthopedic implants and instruments. 1.2 Hospital receiving personnel, central supply personnel, operating room personnel, surg... Språk Publicerad 2004-10-01

PDF · 468 SEK

Standard · ASTM ASTM D3053 Standard Terminology Relating to Carbon Black 1.1 This terminology covers a compilation of definitions of technical terms used in the carbon black and rubber industries. Terms that are generally understood or adequately defined in other readil... Språk Publicerad 2008-05-01

PDF · 468 SEK

Standard · ASTM ASTM F819 Standard Terminology Relating to Electrical Protective Equipment for Workers - Språk Publicerad 2008-05-15

PDF · 468 SEK

Standard · ASTM ASTM G174 Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact 1.1 This test method covers ranking rigid engineering materials for abrasion resistance in rubbing against aluminum oxide abrasive finishing tape. Though most solids can be tested, this test metho... Språk Publicerad 2004-11-01

PDF · 533 SEK

Standard · ASTM ASTM C565 Standard Test Methods for Tension Testing of Carbon and Graphite Mechanical Materials 1.1 These test methods cover the apparatus, specimen, and procedures for the tension testing of carbon and graphite mechanical materials with a grain size smaller than 0.79 mm. 1.2 The values sta... Språk Publicerad 2005-05-01

PDF · 468 SEK

Standard · ASTM ASTM B381 Standard Specification for Titanium and Titanium Alloy Forgings 1.1 This specification covers 39 grades of annealed titanium and titanium alloy forgings as follows: 1.1.1 Grade F-1—Unalloyed titaniu This specification covers 3... Språk Publicerad 2009-07-08

PDF · 533 SEK

Standard · ASTM ASTM D1795 Standard Test Method for Intrinsic Viscosity of Cellulose 1.1 This test method covers the determination of the intrinsic viscosity of purified celluloses such as bleached wood pulps, cotton linters, and regenerated cellulose. It is applicable to all cellu... Språk Publicerad 2007-09-05

PDF · 533 SEK

Standard · ASTM ASTM D5528 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites 1.1 This test method describes the determination of the opening Mode I interlaminar fracture toughness, GIc, of continuous fiber-reinforced composite materials using the double cantilever beam (DCB... Språk Publicerad 2007-05-01

PDF · 611 SEK

Standard · ASTM ASTM E1353 Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture 1.1 This is a fire-test-response standard. 1.2 These test methods are designed for the assessment of the resistance of upholstered furniture component assemblies to combustion after exposure to sm... Språk Publicerad 2008-05-14

PDF · 611 SEK

Standard · ASTM ASTM D4168 Standard Test Methods for Transmitted Shock Characteristics of Foam-in-Place Cushioning Materials 1.1 These test methods determine the shock-absorbing characteristics of foam-in-place packaging materials. 1.2 Test Method A uses a free-fall package drop test appar Språk Publicerad 2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM C1179 Standard Test Method for Oxidation Mass Loss of Manufactured Carbon and Graphite Materials in Air 1.1 This test method provides a comparative oxidation mass loss of manufactured carbon and graphite materials in air. 1.2 The values stated in SI units are to be regarded as standard. No other unit... Språk Publicerad 2005-06-01

PDF · 468 SEK

Standard · ASTM ASTM B861 Standard Specification for Titanium and Titanium Alloy Seamless Pipe 1.1 This specification covers the requirements for 34 grades of titanium and titanium alloy seamless pipe intended for general corrosion resisting and elevated temperat... Språk Publicerad 2009-08-01

PDF · 533 SEK

Standard · ASTM ASTM C325 Standard Test Method for Wet Sieve Analysis of Ceramic Whiteware Clays 1.1 This test method covers the wet sieve analysis of ceramic whiteware clays. This test method is intended for use in testing shipments of clay as well as for plant control tests.This standard doe... Språk Publicerad 2007-09-05

PDF · 468 SEK

Standard · ASTM ASTM D6478 Standard Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints 1.1 This test method covers procedures for determining the ability to fold and pack fabrics used for inflatable restraints using an index of specific packability. 1.2 Procedures in this test method... Språk Publicerad 2008-09-03

PDF · 533 SEK

Standard · ASTM ASTM F1306 Standard Test Method for Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates 1.1 This test method permits flexible barrier films and laminates to be characterized for slow rate penetration resistance to a driven probe. The test is performed at room temperature, by applying ... Språk Publicerad 2008-08-01

PDF · 533 SEK

Standard · ASTM ASTM F2055 Standard Test Method for Size and Squareness of Resilient Floor Tile by Dial Gage Method 1.1 This test method covers the determination of both dimensions (length and width) and squareness of resilient floor tile. This test method is intended for use with square tiles ranging from a no... Språk Publicerad 2009-04-01

PDF · 533 SEK

Standard · ASTM ASTM E1791 Standard Practice for Transfer Standards for Reflectance Factor for Near-Infrared Instruments Using Hemispherical Geometry 1.1 This practice covers procedures for the preparation and use of acceptable transfer standards for NIR spectrophotometers. Procedures for calibrating the reflectance factor of materials on an ab... Språk Publicerad 2008-03-15

PDF · 468 SEK

Standard · ASTM ASTM E1750 Standard Guide for Use of Water Triple Point Cells 1.1 This guide covers the nature of two commercial water triple-point cells (types A and B, see Fig. 1) and provides a method for preparing the cell to realize the water triple-point and calibrate ... Språk Publicerad 2009-05-01

PDF · 533 SEK

Standard · ASTM ASTM B863 Standard Specification for Titanium and Titanium Alloy Wire 1.1 This specification covers titanium and titanium alloy wire as follows: 1.1.1 Grade 1—Unalloyed titanium, low oxygen, This specification covers for titanium a... Språk Publicerad 2009-06-01

PDF · 533 SEK

Standard · ASTM ASTM A707/A707M Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service 1.1 This specification covers forged carbon and alloy steel flanges intended primarily for petroleum and gas pipelines in areas subject to low ambient temperatures. Included are flanges to specifie... Språk Publicerad 2002-09-10

PDF · 533 SEK

Standard · ASTM ASTM E1911 Standard Test Method for Measuring Paved Surface Frictional Properties Using the Dynamic Friction Tester 1.1 This test method covers the procedure for measuring paved surface frictional properties as a function of speed using the Dynamic Friction Tester (DF-Tester). 1.2 The DF Tester consists of a hor... Språk Publicerad 2009-01-01

PDF · 533 SEK

Standard · ASTM ASTM C562 Standard Test Method for Moisture in a Graphite Sample 1.1 This test method provides a practical determination for the percentage of moisture in a graphite sample. 1.2 The values stated in SI units are to be regarded as standard. No other units of meas... Språk Publicerad 2005-06-01

PDF · 468 SEK

Standard · ASTM ASTM D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions 1.1 This test method covers a laboratory screening procedure for evaluating the effectiveness of engine coolants in combating corrosion of aluminum casting alloys under heat-transfer conditions tha... Språk Publicerad 1996-06-10

PDF · 468 SEK

Standard · ASTM ASTM D2369 Standard Test Method for Volatile Content of Coatings 1.1 This test method describes a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings. Test specimens are heated at 110 ±5&... Språk Publicerad 2007-10-10

PDF · 468 SEK

Standard · ASTM ASTM D1868 Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems 1.1 This test method covers the detection and measurement of partial discharge (corona) pulses at the terminals of an insulation system under an applied test voltage, including the determination of... Språk Publicerad 2007-09-05

PDF · 611 SEK

Standard · ASTM ASTM D3666 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials 1.1 This specification covers the minimum requirements for field and laboratory personnel, for establishing and maintaining a quality system, and establishes minimum qualifications for agencies eng... Språk Publicerad 2007-09-05

PDF · 533 SEK

Standard · ASTM ASTM E2072 Standard Specification for Photoluminescent (Phosphorescent) Safety Markings 1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergen... Språk Publicerad 2009-07-01

PDF · 468 SEK

Standard · ASTM ASTM E2073 Standard Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings 1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements. 1.2 When refere... Språk Publicerad 2009-07-01

PDF · 468 SEK

Standard · ASTM ASTM E1153 Standard Test Method for Efficacy of Sanitizers Recommended for Inanimate Non-Food Contact Surfaces 1.1 This test method is used to evaluate the antimicrobial efficacy of sanitizers on precleaned inanimate, nonporous, non-food contact surfaces. 1.2 This test method may also be used to evaluate th... Språk Publicerad 2003-04-10

PDF · 533 SEK

Standard · ASTM ASTM D2013 Standard Practice for Preparing Coal Samples for Analysis 1.1 This practice covers the reduction and division of gross or divided samples, and the preparation of composite samples, up to and including the individual portions for laboratory analysis.1.2 Re... Språk Publicerad 2007-09-05

PDF · 611 SEK

• < Föregående
• 233
• 234
• 235
• 236
• 237
• 238
• 239
• 240
• 241
• 242
• Nästa >