1.1 This test method 2 covers the determination of the resistance to oxidation of nicke
2007-09-05
1.1 This guide covers a nondestructive procedure to determine the form of clean, dry sapphire substrates.1.2 This guide is applicable to substrates 25 mm or larger in diameter, with a minimum thick...
2004-05-01
2011-07-01
1.1 This test method covers the procedure for measurements of internal stresses in organic coatings by using the cantilever (beam) method. 1.2 This method is appropriate for the coatings for which...
2005-02-01
1.1 This specification covers distilled acids derived from the distillation of linseed oil. Two types are covered as follows: 1.1.1 Type I -Usually produced from degummed linseed oil and referre...
1998-05-10
2007-03-20
1.1 This test method covers the determination of performance characteristics of fuel ethanol manufacturing facilities. 1.2 This test method is applicable for all starch, sugar, and combination star...
2006-11-01
2009-09-01
1.1 This test method covers measuring the angular separation of secondary images from their respective primary images as viewed from the design eye position of an aircraft transparency. Angular sep...
2010-08-20
1.1 This practice covers guidance and direction to suppliers, purchasers, and users in the handling, transportation, and storage of HFC–236fa. 1.2 The values stated in either SI units o
2010-06-01
1.1 This specification covers asphalt cement for use in the construction of pavements. 1.2 This specification covers the following penetration grades: This specification covers the standard for asp...
2009-12-01
1.1 This practice covers the confirmation of test flames for small-scale burning tests on plastic materials using the laboratory burner described in Specification D 5025. Back pressures and flow ra...
1.1 This test method covers a standardized procedure for removing volatile materials such as gasoline and water from used engine oils prior to further oil analysis. <div
2008-04-09
1.1 This test method covers infrared procedures for determining the vinyl acetate content of EVA copolymers using pressed films (Procedure A) or molded plaques (Procedure B) and internal correction...
2004-07-01
1.1 This classification covers pairs of scales for classifying an aspect of the serviceability of an office facility, that is, the capability of an office facility to meet certain possible requirem...
2005-05-01
1.1 This test method describes a two-stroke cycle diesel engine test procedure for evaluating engine oils for certain high-temperature performance characteristics, particularly cylinder liner scu...
2009-04-15
1.1 This practice covers the determination of hypoeutectoid steel phase transformation behavior by using high-speed dilatometry techniques for measuring linear dimensional change as a function of t...
2010-05-17
1.1 This test method covers the determination of water in the range from 0 to 25 % volume in petroleum products, tars, and other bituminous materials by the distillation method. Note<
2010-05-01
1.1 This specification covers steel strip, nickel-clad or nickel-plated on both sides, for use in electron tubes.1.2 The values stated in inch-pound units are to be regarded as the standard. The me...
2003-12-01
2009-07-01
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, a This ...
2008-02-06
1.1 This specification covers carbon steel overboard discharge hull penetrations for system piping of NPS 1 through NPS 24 (see Note 1). Note 1—The dimensionless designator NPS (nominal p...
2006-02-01
1.1 This specification covers isophorone (98 % grade) for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard; for purp...
2009-06-01
1.1 This test method covers an electronic hydrogen detection instrument procedure for measurement of plating permeability to hydrogen. This method measures a variable related to hy
1.1 This terminology document covers terminology pertaining to items that are considered fasteners and closures such as buttons, hook and loop touch fasteners, snap fasteners and slide fasteners us...
2011-05-20
1.1 This test method covers the determination of pour point of petroleum products by an automatic instrument that applies a controlled burst of nitrogen gas onto the specimen surface while the spec...
2010-09-17
1.1 This test method will determine the moisture content, as a percentage of the dry weight of organic and inorganic insulation materials. <p
1.1 This specification covers welded UNS N06110 tube in the annealed condition (temper) for general corrosion applications. 1.2 This specification covers outside diameter and nominal wall tube. ...
2006-06-01
1.1 This practice covers the procedures for obtaining quantitative samples of a phytoplankton community by use of depth-integrating sampler. The method is suitable for use in flowi
2004-04-01
1.1 This test method covers two procedures for weather resistance of slate in all outdoor installations by determining the depth of softening by an abraser or by hand scraping. Note</span
2009-04-01
1.1 This guide describes procedures for obtaining data concerning the adverse effects of a test material (not food) added to marine and estuarine waters on certain species of marin
1.1 This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosion-resistan This ...
2013-04-19
1.1 This test method covers and is required to evaluate the performance of engine oils intended to satisfy certain American Petroleum Institute (API) C service categories (included in Specification...
1.1 This guide describes and compares different methods for assessing the potential for, or existence of, depressurization-induced backdrafting and spillage from vented residential combustion appli...
2011-12-16