1.1 This specification covers the requirements for four classes of machinable, high-density tungsten base metal produced by consolidation of metal powder mixtures of which the composition is mainly...
1999-12-10
2007-11-01
1.1 This test method establishes procedures for depressing and releasing a tactile membrane switch to determine the amount of switch teasing, if any.This standard does not purport to address all of...
2007-12-01
1.1 This test method covers the operation, calibration, and data interpretation for an on-line corrosion product (metals) monitoring system. The monitoring system is based on x-ray fluorescence (XR...
2008-05-01
-
2005-06-01
1.1 This guide covers the use of overtesting in order to reduce the required number of parts that must be tested to meet a given quality acceptance standard. Overtesting is testing a sample number ...
2011-06-01
1.1 This specification covers pure aluminum metal (unalloyed) for use as raw material for making evaporation sources, sputtering targets, and superconducting wires. 1.2 This specification sets pur...
1.1 This guide lists the responsibilities of the end user and the infrared thermographer when examining electrical and mechanical systems. 1.2 This guide outlines the specific content required to ...
1.1 This specification covers sputtering targets fabricated from metallic silicides (molybdenum silicide, tantalum silicide, titanium silicide, and tungsten silicide). These targets are referred to...
1.1 This practice describes a method for ultrasonic mapping of the soundness of a bond joining a sputtering target to its supporting backing plate. The results of the examination may be used in pre...
1.1 This guide contains a comprehensive discussion of potential requirements for a sample chain-of-custody program and describes the procedures involved in sample chain-of-custody. The purpose of...
1.1 This specification covers pure aluminum metal (unalloyed) for use in evaporation sources and sputtering targets. This material is intended as a raw material for electronic applications. The mat...
1.1 This test method covers the measurement of common-emitter d-c current gain (forward, hFE, or inverted, hFEI) of bipolar transistors, for which the collector-emitter leakage current, ICEO, is le...
1.1 This test method covers the testing of lightweight concrete aggregates to evaluate the potential degree of staining from iron compounds. 1.2 The values stated in inch-pound units are to be re...
1999-11-10
2007-01-01
1.1 These test methods cover the determination of the in-place density and unit weight of soil and rock using a pouring device and calibrated sand to determine the volume of a test pit. The word "r...
2008-03-01
1.1 This guide describes standardized procedures for the quantitative sensory assessment of fragrance/odor intensity or attribute intensity of fragrances in shampoo or hair conditioner base through...
2006-10-15
1.1 This specification covers lightweight aggregates intended for use in concrete not exposed to the weather, in which the prime consideration is the thermal insulating property of the resulting co...
2007-07-15
1.1 This test method covers the estimation of the resistance of vulcanized rubber to cracking when exposed to an atmosphere containing ozone. The rubber specimens are kept under a surface tensile s...
2007-08-15
1.1 This test method evaluates the ability of a grease to adhere to a metal surface, when subjected to a water spray under prescribed laboratory conditions. 1.2 The values stated in SI units are...
2006-11-01
1.1 The purpose of this terminology is to provide uniform contractions of terms relating to plastics. Abbreviated terminology has evolved through widespread common usage. This compilation has been ...
2007-05-01
1.1 These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains. 1.2 T...
1.1 These test methods are used to estimate the cracking resistance of vulcanized rubber exposed under dynamic strain conditions to a chamber atmosphere containing ozone at a fixed partial pressure...
1.1 This specification covers rigid plastic compounds intended for use in making nonpressure piping products composed of (1) poly(vinyl chloride) polymer, (2) chlorinated poly(vinyl chloride) poly...
2006-12-01
1.1 This practice covers procedures applicable when Practice G 26 is employed for exposure of degradable plastics. Reference is made to sample preparation and evaluation of test results. 1.2 This...
2007-01-11
1.1 This test method covers a standard means of testing the laser resistance of the shaft of a tracheal tube. 1.2 This test method addresses the laser resistance of the shaft of the tracheal tube...
1.1 This guide covers uniform methods for expressing temperature, temperature values, and temperature differences. 1.2 This guide is intended as a supplement to Practice E380.
1.1 This specification covers unalloyed tungsten plate, sheet, and foil. 1.2 The values stated in inch-pound units are to be regarded as the standard.
1.1 This practice defines test conditions applicable when Practices D1435 and G7 are employed for the outdoor exposure testing of photodegradable plastics. 1.2 This standard does not purport to a...
2008-08-01
1.1 This standard includes those items related to statistical aspects of sampling.
2008-10-01
1.1 This test method covers the measurement of the molding index of thermosetting plastics ranging in flow from soft to stiff by selection of appropriate molding pressures within the range from 4.1...
2008-09-24
1.1 This test method covers four procedures for making, curing, and testing specimens of concrete stored under conditions intended to accelerate the development of strength. The four procedures are...
2012-04-18