1.1 This specification covers composite ribbed steel pipe, precoated and polyethylene lined intended for use for gravity flow sanitary sewers, storm sewers, and other special applications such as w...
2008-05-01
1.1 This test method covers the determination of the coefficient of specific permeability for the flow of air through rocks. The procedure establishes representative values of the coefficient of pe...
2008-11-05
1.1 This test method is an index test which provides a procedure for determining the breaking load (grab strength) and elongation (grab elongation) of geotextiles using the grab method. This test ...
1.1 These test methods cover the analysis of acrylonitrile. 1.2 The analytical procedures appear in the following order: <td align="ce
2008-12-15
1.1 This test method covers the use of ultrasonic film thickness gages to measure accurately and nondestructively the dry film thickness of organic coatings applied over a substrate of dis...
2008-09-03
1.1 This practice is for the evaluation of coatings used in below grade applications to resist the passage of water through concrete block. 1.2 The values stated in SI units are to be regarde...
1.1 This test method covers the determination of the shrinkage temperature of all types of leather. The heating medium is water when the shrinkage temperature is at or below 98°C. The he...
2008-12-03
1.1 This specification covers solder metal alloys (commonly known as soft solders) used in non-electronic applications, including but not limited to, tin-lead, tin-antimony, tin-antimony-copp...
2008-06-04
1.1 This practice outlines the necessary steps for the identification of elements in a given Auger spectrum obtained using conventional electron spectrometers. Spectra displayed as either the elect...
2009-01-15
1.1 This test method describes a procedure for determining the total peroxide content of acrylonitrile in the range of 0.1 to 0.6 mg H2O2/kg acrylonitrile (ppm). Peroxides are an undesirable impuri...
1.1 This terminology document defines terms commonly used in standards developed by ASTM Committee E47 on Biological Effects and Environmental Fate. This terminology document is intended to be con...
2008-04-09
1.1 This guide covers the use of the Incident Command System (ICS), as developed in the National Incident Management System (NIMS) in 2004, as the management framework for search and rescue (SAR) ...
2008-11-01
1.1 This specification covers total ankle replacement (TAR) prostheses used to provide functioning articulation by employing talar and tibial components that allow for a minimum of 15° o...
2009-02-01
1.1 This test method describes the measurement of Reaction Induction Time (RIT) of chemical materials that undergo exothermic reactions with an induction period. The techniques and apparatus descri...
2008-04-01
1.1 This practice describes the procedure used to determine the effect of cleaners on unpainted aircraft surfaces. Visual observation is used for determining streaking or permanent stains which req...
2008-12-01
1.1 This test method covers the determination of total acidity as acetic acid in concentrations below 500 μg/g in acrylonitrile. 1.2 The values stated in SI units are to be regarded as
1.1 This test method covers the preparation, equipment, test procedure, and data documentation for determining in situ creep characteristics of a rock mass using a rigid plate subjected to control...
1.1 This test method covers several ground penetrating radar (GPR) evaluation procedures that can be used to evaluate the condition of concrete bridge decks overlaid with asphaltic concrete wearing...
1.1 This test method covers the on-line determination of dissolved oxygen (DO) in water samples primarily in ranges from 0 to 500 μg/L (ppb), although higher ranges may be used for cali...
1.1 This test method covers the quantitative determination of residue in emulsified asphalts composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. 1.2 The...
1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in resilient flooring sealed by the heat weld method. 1.2 This standard does not pu
1.1 This specification covers aluminum 1350-H19 (extra hard), 1350-H16 or -H26 ([n ]hard), 1350-H14 or -H24 (1/2 hard) and 1350-H142 or -H242 (1/2 hard) bare compact- This specification covers alum...
1.1 This test method describes the gas chromatographic determination of glycol impurities in Mono-, Di- Tri- and Tetraethylene Glycol (MEG, DEG, TEG and TeEG) in the range of 5 to 3000 mg/kg. 1.2 T...
2008-08-06
1.1 This test method covers the determination of the ambient local stresses in a rock mass and the equipment required to perform in situ stress tests using a three-component borehole deformation g...
1.1 This practice covers the installation and preparation of the thick poured lightweight cellular concrete underlayments over wood structural panel subfloors in commercial structures or over concr...
1.1 This test method covers the determination of anionic impurities in 50 % caustic soda (sodium hydroxide) and 50 % caustic potash (potassium hydroxide) solutions using ion chromatography (IC). An...
1.1 This specification describes all the work required to structurally reinforce, seal, and protect sanitary sewer manholes. Applications include applying a prepackaged cementitious liner that can ...
2009-05-01
1.1 This practice specifies a data format for numerically-controlled cutting machines for fabric. 1.2 This standard uses a subset of the defined instruction set defined in ANSI/EIA-274-D in additio...
1.1 This test method covers a laboratory procedure for subjective determination of the existence, nature, and degree of odors present in all types of thermal insulation materials. This test method ...
1.1 The visual surface preparation standards consist of a series of color prints available as separate publications. Five different sets of photographs are described in this stan...