1.1 This test method describes the method used and the calculation of results for the determination of the in-vitro biol
2007-03-14
1.1 This guide covers a procedure for obtaining subjective numerical ride ratings for a group of representative highway pavement sections having a broad spectrum of physical characteristics. 1.2 Th...
2003-12-01
1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) 0.060 through 0.625 thread sizes and flat countersunk (SFHCS) 0.060 through 1.5 t...
2012-08-17
1.1 This practice addresses the instrumental measurement requirements, calibration procedures, and material standards needed for obtaining precise bispectral photometric data for computing the colo...
2007-02-07
1.1 This test method covers a procedure for sampling and determining concentrations of non-methane organic compounds (NMOC) in ambient, indoor, or workplace atmospheres. 1.2 The test method descri...
2009-10-01
1.1 This specification covers acrylonitrile-butadienestyrene (ABS) pipe produced by single extrusion or simultaneous multiple coextrusion, in standard thermoplastic pipe dimension ratios and pressu...
2005-05-01
2007-03-28
1.1 This specification covers “iron” wire with Class A, Class B, and Class C zinc coatings, suitable for use in telephone, telegraph, and signal transmission. This specificat...
2009-11-01
1.1 This test method describes a procedure for determining the effect of exposure to alkaline environments on the strength of cellulose fibers. An alkaline environment is defined t
2008-06-01
1.1 This is an acceptance specification for the ultrasonic inspection of forged steel crankshafts having main bearing journals or crankpins 4 in. [100 mm] or larger in diameter. 1.2 This specifica...
2006-03-01
1.1 These test methods provide procedures for stressing photovoltaic modules in simulated temperature and humidity environments. Environmental testing is used to simulate aging of module mater...
2009-04-01
1.1 This practice (1,2) covers the basic principles for establishing related unit stresses and stiffness values for design with visually-graded solid sawn structural lumber. This practice starts ...
1.1 This specification covers requirements for HCFC Blend B as a fire-fighting medium. 1.2 This specification does not address the fire-fighting equipment or hardware that employs HCFC Blend B or t...
2011-10-14
1.1 This practice identifies the information to be provided through the use and care booklet accompanying a particular model of vacuum cleaner. 1.2 Included is information that the user needs to op...
2006-01-01
1.1 This guide covers the description of carbide structures in annealed high carbon bearing steels. 1.2 Included is a guide for rating steel specimens by a graded series of photomicrographs showing...
1.1 This specification describes glass cullet recovered from municipal waste destined for disposal. The recovered cullet is intended for use in the manufacture of glass fiber used for insulation-ty...
1998-09-10
1.1 This specification covers requirements for glass burets of precision and general-purpose grades suitable for laboratory use. This specification covers requirements for glass burets...
2002-10-10
1.1 This specification covers electric-fusion-welded steel pipe with filler metal added, fabricated from pressure vessel quality plate of several analyses and strength levels and suitable for high...
2011-05-20
1.1 This specification covers three strength grades of slag cement for use as a cementitious material in concrete and mortar. This specification covers three strength grades of finely gr...
1.1 This test method covers the determination of the acidity in aviation turbine fuel in the range from 0.000 to 0.100 mg KOH/g. 1.2 The values stated in SI units are to be regarded as standard. No...
2011-09-16
1.1 This test method covers the quantitative assessment of the amount of residue obtained from metallic medical components when extracted with aqueous or organic solvents. 1.2 This test method does...
2012-04-20
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain inter...
2012-06-20
1.1 This safety specification is intended to reduce injuries and deaths of children from hazards associated with tipover of clothing storage units. 1.2 This safety specification covers chests, dres...
2009-08-01
1.1 This practice is intended to evaluate changes in kinetic performance of ion exchange resins used in mixed beds to produce high purity water. Within strict limitations, it also may be used for c...
2004-06-01
1.1 This guide covers the general technique of “spiking” a broad range of materials into aqueous media. This guide will serve the analyst in preparing spiked samples fo
2006-08-15
1.1 This test method is intended to be used for calibration and characterization of primary terrestrial photovoltaic reference cells to a desired reference spectral irradiance distribution, such a...
2010-09-17
1.1 This practice covers a system of general classification for the basic rubbers both in dry and latex forms determined from the chemical composition of the polymer chain. 1.2 The purpose of this...
2010-02-01
1.1 This guide covers a series of options but does not specify a course of action. It should not be used as the sole criterion or basis of comparison and does not replace or relieve professional ju...
2004-05-01
1.1 This test method covers evaluation of the energy consumption and refrigeration performance of refrigerated buffet and preparation tables. The food service operator can use this evaluation to se...
2004-10-01
1.1 This specification covers toluene for toluene diisocyanate (TDI) feedstock. 1.2 The following applies to all specified limits in this specification: for purposes of determining conformance wi...
2009-12-01
1.1 This test method covers the determination of the evaporative resistance of clothing ensembles. It describes the measurement of the resistance to evaporative heat transfer from a heated sweating...